Cool-Space 401 Support
Warranties
Installation
Kits & Accessories
About Cool-Space 401
How does the cooler work?
As air passes through the wet cooling media (pads), it absorbs the moisture. This moisture absorbs the heat in the air, reducing the air temperature the same way rain does on a hot summer day.
Does the cooler add humidity?
Yes, but only a slight amount. The area needs a constant flow of fresh air to prevent the air from being re-humidified.
How much of a decrease in temperature does the cooler provide?
Typically the cooler provides an 8- to 33-degree drop depending on the existing dry bulb temperature and relative humidity.
How much water does the cooler use?
On average, the cooler uses 2 to 10 gallons of water per hour depending on the dry bulb temperature and relative humidity.
Does the cooler spray or mist water?
No, moisture is added to the air in a vapor state. As a result, the cooler will not create puddles or wet spots.
How long does the cooling media (pads) last?
The cooling media will last 1 to 2 years, depending on the care it receives. If you have hard water, using the water treatment tabs available by calling Big Ass Fans will help prolong the life of the media.
How effective is the cooler in humid climates?
The air temperature and relative humidity will determine the effective temperature drop. Even in humid climates, you can expect around an 8 degree temperature drop. This drop in temperature combined with the cooler’s high velocity fan can create a chill factor of 15–20 degrees.
Trouble with Something Else
Pump motor will not run when switch is turned on.
Turn fan on to check for power.
- If fan does not start, check breaker and make sure cord is plugged in.
- If fan starts, check for power to and through pump switch (when turned on).
Make sure cooler is filled with water. Pump automatically shuts off if water level is too low.
Fill water reservoir.
Pump motor hums when switch is turned on but does not pump water.
Obstruction in impeller.
Remove object(s).
Pump motor failure.
Replace pump.
Breaker trips or fuse blows when switch is turned on.
Check power cord length and breaker rating.
Refer to operation and maintenance manual for cooler amperage draw and to determine required cord gauge and circuit size.
Check for locked up pump.
Replace pump.
Pump runs but does not pump water.
Air lock in outlet side of pump.
Turn off and on to bleed.
Ensure the impeller is turning in pump.
If not, replace pump.
Floor at side of cooler is wet.
Water inlet hose is loose at supply hose or inlet hose is loose at bulkhead fitting.
Tighten connections and/or replace hose washers.
Water overflows from reservoir or is spitting through fan.
Float valve hose is loose at bulkhead fitting or at float valve.
Tighten connections and/or replace hose washers.
Water pressure is too high to allow float valve to shut off (120 PSI max).
Reduce water pressure by adding an inline reducer.
Float valve is not properly seated.
Check all hoses for leaks.
Water is spitting from the cooler.
Check the hose and valve assembly.
- Reduce flow control setting.
- Replace cracked hose and valve assembly.
- Tighten hose connections.
- Adjust spray bar.
- Ensure pads are installed correctly.
Water is leaking from the drain plug.
Check for worn washer or stem or open drain valve.
- Replace washer.
- Replace drain valve.
There are too many dry streaks on the pads.
Check for blocked holes in the spray bar or adjust water flow.
- Remove spray bar and plug and clean the tube and holes.
- Open water flow control valve.
Cooler will not fill.
Check float screen.
Clean.
Float not functioning.
Replace.
Scale and mineral buildup on cooling media.
Drain and clean the cooler and cooling media.
Add the specified number of water treatment tablets to the reservoir.
- Cool-Space 300: 1 tablet
- Cool-Space 400/401: 2 tablets
- Cool-Space 500: 3 tablets
Fan will not run and makes no sound.
Check power cord, extension cord, switches, and circuit breaker.
- Reconnect power or extension cord.
- Reset breaker.
Fan will not run and makes humming sound.
Blade is in contact with shroud.
Re-center blade hub.
Motor stall (will not turn by hand).
Replace motor.
Breaker trips or fuse blows when fan starts.
Motor stall.
Replace motor.
Check power source.
Refer to cooler operation and maintenance manual for electrical requirements. Upgrade power supply.
Extension cord gauge is too small.
Replace with heavier cord.
Motor overheats, shuts off, and restarts several minutes later.
Extension cord gauge is too small.
Replace with heavier cord.
Inlet air is obstructed or too close to wall.
Provide minimum 3 ft (0.9 m) inlet clearance.
Faulty motor.
Replace motor.
Fan motor will not run and switch makes soft clicking sound.
Ensure switch is making good contact.
Replace switch if needed.
Fan blade does not turn and cooler makes squealing sound.
Motor stall (will not turn by hand).
Replace motor.
Fan will not reach speed but turns and makes humming sound.
Check capacitor (where visible) and motor electrical connections.
Replace capacitor or motor.
Extension cord gauge is too small.
Replace with heavier cord.
How do I replace my cooler’s pump?
WARNING: ELECTRICAL SHOCK HAZARD. Disconnect the power supply before performing service or maintenance. Failure to do so may result in serious injury or death.
- Unscrew fitting from pump.
- Unplug cord from top of pump by removing the two (2) screws.
- Remove pump from water sump and install new pump.
- Perform the steps above in reverse to reconnect the wiring, lift the pump bracket, and reconnect the hose.
- Secure wires to fan frame with wire ties so that wires are clear of fan blades. Ensure plug is positioned correctly.
- Reinstall cooling pads and guards.
- Reconnect power and test pump.
How do I replace my cooler’s fan motor?
WARNING: ELECTRICAL SHOCK HAZARD. Disconnect the power supply before performing service or maintenance. Failure to do so may result in serious injury or death.
- Remove cap from bottom of motor. Disconnect wires and clip wire ties.
- Remove the four (4) fan mounting bolts from front. Support fan to ensure it does not fall.
- Pull the fan out of the cooler.
- Remove blade mounting nut and blade.
- Remove mounting arms by loosening the eight (8) bolts securing the arms to the motor. Note the positions of the arms for re-installation.
- Install arms and blade on new motor.
- Install fan in opening and secure with mounting bolts.
- Reconnect wires. Attach cord to motor arm with wire ties so that wires are clear of fan blades.
Still Need Help?
Call our exceptional customer service team for help with all your fan-related questions.