Powerfoil 6 HVLS Fan Support
Videos
Mounting: Bar Joists (Spans 8 ft or Less)
Mounting: Bar Joists (Spans More Than 8 ft)
Mounting: I-Beam
Mounting: Z-Purlins
Mounting: Solid Wood Beam
Lenze Keypad Err on run / speed
Lenze keypad operation
Bafcon – Setting Schedules
Bafcon – Controlling Lights
Bafcon – Setting/Changing passcode
Bafcon – Do I have the latest version
WSC changing parameters
Fire Relay Install
WSC – Setting and removing Passcode
Mounting: Bar Joists (Spans More Than 8 ft)
Mounting: I-Beam
Mounting: Z-Purlins
Mounting: Solid Wood Beam
Lenze Keypad Err on run / speed
Lenze keypad operation
Bafcon – Setting Schedules
Bafcon – Controlling Lights
Bafcon – Setting/Changing passcode
Bafcon – Do I have the latest version
WSC changing parameters
Fire Relay Install
WSC – Setting and removing Passcode
Installation
Mounting: Bar Joists (Spans 8 ft or Less)
Mounting: Bar Joists (Spans More Than 8 ft)
Mounting: I-Beam
Mounting: Z-Purlins
Mounting: Solid Wood BeamPre-Installation Checklist & Guidelines
Bar Joist Mounting Preparation
Fan Installation
Direct Mount
Extension Tube Cutting Instructions
Electrical Guidelines
Standard Controller
BAFCon Controller
Powerfoil 6 Installation Guide
Safety Guidelines
Direct Mount
Wired Standard Control
BAFCon
Kits & Accessories
Operation & Maintenance
About Powerfoil 6 HVLS Fan
Do I need to install guy wires with my Powerfoil 6 fan?
Yes,Ā guy wires are required if:
- The extension tube isĀ 4 ft (1.2 m) or longer
- The fan is installedĀ outdoors
- The fan is nearĀ fixtures or exposed to high wind
- They are included in qualifying fan packages and are critical for stability and warranty compliance.
What kind of electrical circuit do I need for installation?
Each fan requires aĀ dedicated overcurrent-protected circuit:
- 20 A @ 200ā240 VAC, single-phase
- 15 A @ 200ā240 VAC, three-phase
- 10 A @ 400ā480 VAC, three-phase
Refer to NEC Article 430 and local codes for conductor sizing and protection requirements.
Can I mount Powerfoil 6 to any beam or structure?
Powerfoil 6 can be mounted to:
- I-beams (with restrictions)
- Bar joists (with angle iron)
- Solid beams and Z-purlins (with special kits)
However,Ā fabricated I-beamsĀ andĀ strut channels (Unistrut)Ā are not recommended unless approved by a structural engineer.
How do I maintain my Powerfoil 6 fan?
Big Ass Fans recommends:
- AnĀ annual inspectionĀ of hardware, guy wires, and safety cables
- Checking forĀ oil leaks, cracks, or corrosion
- Ensuring properĀ torqueĀ on bolts and fasteners
- Cleaning withĀ non-chlorine-based degreasers
See the fullĀ Annual Maintenance ChecklistĀ in the installation guide.
What should I do if my fan doesnāt start after installation?
- Check allĀ power and control wiringĀ for secure connections
- Ensure the circuit is providing the correctĀ voltage and amperage
- Make sure anyĀ fire relay wiringĀ is properly configured
If issues persist, contactĀ Big Ass Fans Customer ServiceĀ at 877.244.3267.
Still Need Help?
Call our exceptional customer service team for help with all your fan-related questions.
