Big Ass Fans

Powerfoil D Support

FAQs

Controlling Powerfoil D

Do I operate the ion technology separately from the fan?

No. The Big Ass Fans’ Clean Air System ionizer will operate at any point when your Big Ass fan is receiving power.

How do I operate my fan?

Click here for information on operating your fan with the standard controller.

Click here for information on operating your fan with the BAFCon controller.

Click here for information on operating your fan with the keypad controller.

Video: 

Video: 

My fan will not start.

Make sure all wires are securely connected and that supply power is adequate and functional. If the fan still does not start, contact Customer Service.

How do I enable/disable my fan’s occupancy sensor using the standard controller?
  1. Press and hold the standard controller  and + buttons until the Menu screen appears.
  2. Press + until you reach the Motion Sense screen, and then press the power button to enable/disable the occupancy sensor.
  3. Press  to exit the settings menu.
How do I adjust my fan’s occupancy sensor settings using the standard controller?
  1. Press and hold the standard controller  and + buttons until the Menu screen appears.
  2. Press + until you reach the Motion Sense screen, and then press the power button to enable the occupancy sensor.
  3. Press + to navigate to the Motion Timeout screen. Motion timeout specifies how much time should pass after no motion is detected before the occupancy sensor turns the fan off.
  4. Press the power button to adjust the motion timeout: 30 minutes (default), 1 hour, 2 hours, 4 hours, or 8 hours.
  5. Press – to exit the settings menu.
How do I enable/disable my fan’s occupancy sensor using the BAFCon controller?

On the BAFCon Home screen, tap the menu icon, and then tap > FAN MANAGEMENT > Fan Name > Motion Sense. Tap the slider next to Enable Motion Sense to enable or disable it.

How do I adjust my fan’s occupancy sensor settings using the BAFCon controller?

On the BAFCon Home screen, tap the menu icon, and then tap > FAN MANAGEMENT > Fan Name > Motion Sense. Tap the slider next to Enable Motion Sense to enable it, and then adjust the settings.

  • Occupancy (Auto On, Auto Off): Select this option if you want the fan to turn off when no motion is detected and turn on when motion is detected again.
  • Vacancy (Manual On, Auto Off): Select this option if you want the fan to turn off when no motion is detected and remain off when motion is detected again. The fan must be turned back on manually each time it is turned off by the occupancy sensor.
  • Motion Sense Timeout: Specify how much time should pass after no motion is detected before the occupancy sensor turns the fan off: 30 minutes (default), 1 hour, 2 hours, 4 hours, or 8 hours.
  • Unoccupied Behavior: Specify what the fan should do when no motion is detected: turn off or mix warm air near the ceiling with cooler air near the floor at a low speed.

Trouble with Something Else

What do I do if the ion generators get wet?

Turn the fan on immediately after the ion generators get wet to dry the generators.

A popping noise is coming from my fan.

Airfoil noise occurs when airfoils are not tightened to the specified torque. Disconnect the fan from power, and then tighten the airfoil hardware to 29 ft·lb (39.3 N·m). Note: If the hardware is stainless steel, tighten the airfoil hardware to 10 ft·lb (13.6 N·m). If popping still occurs, verify that the airfoils are not contacting each other. If they are, contact Customer Service.

My fan wobbles during operation.
  • Verify that the mounting structure is rigid enough to support the fan and that the fan is not being exposed to external air forces.
  • If guy wires were installed, confirm proper installation. If guy wires were not installed, contact Customer Service.

Still Need Help?

Call our exceptional customer service team for help with all your fan-related questions.

+61 1300 244 277

FAQs